基础信息Product information

产品名称：爱斯佩克高低温试验箱ESPEC ARL-0680-AE

产品型号：

更新时间：2025-03-09

产品简介：

爱斯佩克高低温试验箱ESPEC ARL-0680-AE系列产品适用标准：GB/T2423.3 / IEC60068-2-78、GB/T2423.4 / IEC60068-2-30、GB/T2423.34 / IEC60068-2-38、GB/T2423.22 / IEC60068-2-14、JESD22-A100-C、JESD22-A101-C。

产品特性Product characteristics

    中国电子行业仪器优质供应商——坚融实业JETYOO INDUSTRIAL & 坚友仪器JETYOO INSTRUMENTS，专业为中国区用户提供爱斯佩克高低温试验箱ESPEC ARL-0680-AE系列产品仪器设备、技术培训与售后维修服务，Support、销售Sale、服务Service，3S公司，为上?；厍患乙约际跷枷虻囊瞧髯酆戏裆?，是您值得信赖的电子行业仪器专家。

    爱斯佩克高低温试验箱ESPEC ARL-0680-AE系列产品适用标准：GB/T2423.3 / IEC60068-2-78、GB/T2423.4 / IEC60068-2-30、GB/T2423.34 / IEC60068-2-38、GB/T2423.22 / IEC60068-2-14、JESD22-A100-C、JESD22-A101-C。

系列产品产品规格书
1. 型号
2. 试验箱容量
3. 电源 电源电压变动：额定值的±10%
4. zui大负载电流
5. 调温调湿方式 平衡调温调湿方式（BTHC 方式）
6. 可运行条件 环境温度：0～＋40℃
环境湿度：zui高75%rh（30℃ 75%rh 露点以下）
7. 性能 温度箱以IEC 60068-3-5：2001、JTM K07：2007 为标准，湿度箱以IEC 60068-3-6：2001、
JTM K09：2009 为标准。根据周围环境条件的不同，可能会有无法满足规格性能的情况。
为环境温度在＋20℃时，额定电压、无试样时的性能。
7.1 温度性能
ARL-0680-AE  ，ARL-1100-AE
温度范围－45～＋180℃   －45～＋180℃
温度波动±0.3K   ±0.3K
温度斜率3.0K   3.0K
试验箱容量680L   1100L
AC380V
3φ 4W
50Hz(CE 规格*1)
AC400V
3φ 4W
50Hz(CE 规格*1)
0680 23A 22A
1100 25A 23A
*1 符合欧盟(EU)指令的CE 标识。以下称CE 规格。

7.1.4 空间温度偏差
3.0K 3.0K
7.1.5 温度变化速度
除去zui高/zui低温度间的上下10%，且在温度变化范围内的温度变化速度。
上升速度（平均） －22.5℃→＋157.5℃
6.3K/分 4.7K/分
下降速度（平均） ＋157.5℃→－22.5℃
4.8K/分 4.4K/分
下降速度（平均） 环境温度＋25℃时
4.1K/分 4.1K/分
根据环境温度的变动，温度变化速度（下降）按下图所示变化。
ARL－0680
ARL－1100
温度变化速度[K/分]
环境温度 [℃]
温度変化速度 [K/分]
环境温度 [℃]
7.1.6 温度极值达到时间
zui高/zui低温度的到达时间
上升时间 ＋20℃→＋180℃
0680 1100
30 分钟以内 40 分钟以内
下降时间 ＋20℃→－45℃
0680 1100
50 分钟以内 50 分钟以内
下降时间 ＋20℃→－45℃， 环境温度＋25℃时
0680 1100
62 分钟以内 62 分钟以内
根据环境温度的变动，温度极值到达时间（下降）如下图所示变化。
7.1.7 允许发热负荷
箱内温度：＋20℃时
0680 1100
4500W 4500W
7.2 温湿度性能
7.2.1 温度范围
0680 1100
10～95℃ 10～95℃
7.2.2 湿度范围
0680 1100
10～98%rh 10～98%rh
环境温度 [℃]
温度极值到达时间 [分]
注）箱内温度40℃以下运行时，冷却器（兼除湿器）会结霜， 连续运行将受限制。
7.2.3 湿度波动
0680 1100
±2.5%rh ±2.5%rh
7.2.4 湿度斜率
0680 1100
10%rh 10%rh
7.2.5 空间湿度偏差
0680 1100
10%rh 10%rh
7.2.6 允许发热负荷
箱内温湿度：＋85℃ 85%rh 时
0680 1100
500W 500W
7.3 噪音
噪音的测量在无声响的室内进行， 为试验箱正面1m、高1.2m 处的值（JIS-Z-8731:1999 A 特
性）。受安装环境影响，周围的声响等会增加噪音值，须注意安装环境。
0680 1100
61dB 62dB
8 结构
8.1 构成材料
8.1.1 外壳 不锈钢板（SUS430 CP、表面拉丝处理）
8.1.2 内箱 不锈钢板（SUS304 CP、#400 表面处理）
8.1.3 隔热材 玻璃棉＋酚醛泡沫
8.2 试验室 调温调湿室＋试验箱
8.2.1 调温调湿室 导风板、送风机、加热器、冷却器（兼 除湿器）、加湿器、空烧防止器、
加湿器供排水口、吸气栅
8.2.2 试验箱 干球温度检出端子、湿球温度检出端子、纱布盘、电缆孔、
试验箱排水口、排水口用用罩子、顶部面板、
搁板支架
zui大承重 地面承重 （支架承重和地面承重的总和 试验箱承重量 ）
0680 80 ㎏
（含搁板重量）
80 ㎏
（均匀分布） 80 ㎏
1100 100 ㎏
（含搁板重量）
150 ㎏
（均匀分布） 150 ㎏
8.3 门 门把手（右把手、左铰链、带钥匙）、一扇门、门锁解除装置、箱门接水盘、
温湿度程序指示调节器（彩色LCD 显示、通过触摸屏设定）、
操作开关、温度过升防止器
8.4 控制盘 主电源开关（负载开关或漏电开关）、试样电源控制端子、
时间信号端子、通信端口、试样温度输入端子
8.5 水回路室 加湿水用泵、湿球纱布供水用泵、加湿排水用泵、
机械室排热孔（顶部）
8.6 机械室 压缩机单元、压缩机接露盘、冷凝器风扇、凝水盘、排水管、
机械室排热孔（后部）、供水箱、冷凝器过滤器
8.7 电源线插入孔 顶部或背面任意选择一个
8.8 排水管 背面一处（3 根）
8.9 供水（直连）口 背面一个
9. 尺寸和重量
9.1 尺寸
0680 1100
内尺寸 850×1000×800 1100×1000×1000
外尺寸 1050×1955×1805 1300×1955×2005
不含突出部分 (W×H×D ㎜)
9.2 重量
0680 1100
510 ㎏ 600 ㎏
10. 加热器 镍铬合金电热丝加热器：6kW（3kW×2 个）
11 加湿器 SUS316 铠装加热器（表面蒸发式）
0680 1100
4kW（2kW×2 个） 5kW（2.5kW×2 个）
12 冷却器 板翅式冷却器（兼除湿器） 1 个
13 冷冻方式 机械式单段压缩冷冻方式
13.1 压缩机 旋涡式压缩机
13.2 冷凝器 空冷式冷凝器
13.3 膨胀机构 电子式自动膨胀阀
13.4 压缩机容量
0680 1100
3.0kW 3.75kW
13.5 冷媒 R404A

14. 计装
名称 N 计装 P-310
构成 用户界面、主机、I/O
显示部功能
带触摸屏
7.0 英寸彩色LCD
背光 LED（寿命 50,000 小时）
驱动方式 ＴＦＴ
显示像素数 800x480（WVGA）
状态显示LED 外部存储指示灯、通信指示灯、定时预约指示灯、
电源指示灯
硬件开关 带电源指示灯的电源开关（按钮式）
控制功能 温湿度控制功能
控制方式
PID 控制（对应试样温度控制）
温度输入
试验箱温度(JIS T 型热电偶）
试样温度控制(JIS T 型热电偶)
湿度输入
试验箱干湿球温度输入方式(JIS T 热电偶）
输入功能
100ms 高速取样功能、断线检测功能
调整功能
温度偏离设定功能
调整范围 ±5.0℃
设定zui小分辨率 小数点后1 位
运行模式 定值运行、程序运行、远程运行、停止
运行设定
定值设定
可设定数 3 模式
设定范围及分辨率
温度 －50.0℃～＋185.0℃、以0.1℃为单位
湿度 0%rh～100%rh、以1%rh 为单位
设定功能
试样温度控制设定、湿度控制 OFF 设定、压缩机设定、时间信号
设定、上下限报警设定、上限偏差报警设定、定值模式名称
设定
程序设定
可设定数 40 模式（每个模式zui多99 步骤）
设定范围及分辨率
温度 －50.0℃～＋185.0℃、以0.1℃为单位
湿度 0%rh～100%rh、以1%rh 为单位
时间 0 小时 1 分钟 ～9999 小时59 分钟、以1 分钟为单位
设定功能（除定值的设定功能外还包含以下设定功能）
温度斜率设定、湿度斜率设定、曝露时间设定、暂停设定、开始
条件设定、结束条件设定（程序间可链接）、计数设定(A,B)、程序
名称设定、程序列表显示
语言 日语、英语、中文（简体字、繁体字）、韩语
（无需再启动，通过画面设定实现切换）
名称 N 计装 P-310
附属功能
标准功能
基本功能
运行操作功能、报警功能、信息功能、附件功能（时间累计器、排水设定）、帮助功能、箱内监视功能（温度湿度、外部输出、趋势图）、追溯功能
管理设定功能
定时设定（开始定时、结束定时、快速定时）、取样设定、?；ど瓒?、报警历史显示、版本信息、定期点检维护一览显示、通知功能、带重置功能的计时器、add on/系统更新历史显示
维护设定功能
通信设定(LAN设定)、设备运行动作设定（停电复位动作设定、备份运行设定、门开放时动作设定）、设定到达判定条件设定、时间信号名称设定、画面设定、声音设定、日期?屏幕设定、用户密
码登录、偏离调整、设备详细设定（电源频率、纱布连续供水设定）、试样温度控制环境设定
选购功能 通信功能(RS485, RS232C, GPIB)、记录仪设定功能（输出项目设定）、外部报警输出设定功能、加湿延迟功能
外部存储功能
接口
USB2.0 标准
（插口A 型）
500mA(zui大）
对应设备 USB 大容量闪存卡
对应文件格式 FAT16/FAT32
对应功能
?取样写入设定
?程序模式写入/读取
?追溯数据写入
?add on/系统更新
对应ＰＣ应用 模式manager Lite
※模式manager Lite 可在Test Navi 产品会员下载。
网络功能
接口
Ethernet 接口
（100baseTX)
通信协议 TCP/IP(HTTP, SMTP,IPv4)
Web 应用
监视功能、设定功能、 运行操作功能、
数据收录功能、管理设定?维护设定功能、
电子邮件通知功能
对应浏览器
Windows Internet Explorer10
PC 通信功能 Ethernet 接口 和ＰＣ 1 対1 连接
动作环境
性能保证环境 温度＋23℃±5℃、湿度30%rh～90%rh（无结露）
动作保证环境 温度0℃～＋60℃、湿度30%rh～90%rh（无结露）
保存环境 温度－20℃～＋70℃、湿度20%rh～95%rh（无结露）
显示精度
温度（T 型热电偶）
（环境温度 ＋23℃±1℃时）
测量精度 ±0.3℃
显示精度（满量程） ±(0.07%FS+1digit)
时间 月差 60 秒以内 +23.0℃±5℃
9 爱斯佩克株式会社
15. 主电源开关
负载开关（AC380V/AC400V）
主电源开/关用
（1）额定电压 AC380V/AC400V 3φ N/PE 50Hz
主电源未配备断路器。
须设置断路器（32A SLOW）。
（2）额定电流 32A
16. 箱内循环用送风机 多叶片风扇
16.1 驱动方式 电动机直结方式
16.2 电动机 100W 2 个
17. 冷凝器用送风机 低噪音型有压换气扇
100W 2 个
18. 装备品
18.1 电缆孔 右侧面 φ100 ㎜ 1 个
左侧面 φ100 ㎜ 1 个
18.2 脚轮 自由脚轮 4 个
18.3 调整脚 4 个
18.4 时间信号端子
试验状态报* 接点容量 AC250V 1A 2 点
18.5 试样电源控制端子
试验?；び?接点容量 AC250V 3A 1 个
18.6 试样温度输入端子 1 个
18.7 电源线 不附带。
19. 附件
19.1 电缆孔橡胶栓 φ100 ㎜ 硅胶海绵橡胶 2 个
19.2 支架
19.2.1 搁条 不锈钢板（SUS304 CP） 1 组
19.2.2 搁板 不锈钢线（SUS304） 1 张
外尺寸 搁板重量 搁板承重
（均匀分布）
0680 817×27×750 6 ㎏ 40 ㎏
1100 1067×28×950 12 ㎏ 50 ㎏
（W×H×D ㎜）
编号 4412001007021
19.3 玻璃管保险丝 B 型 250V 0.4A、5A、8A 各1 根
19.4 湿球纱布 纱布 24 张、吸管 1 根 1 盒
19.5 试样温度测定用热电偶
T 型热电偶（3m）（IEC 60584-1：1995） 1 根
19.6 试样温度输入接口 1 个
19.7 用户操作手册 CD、设置要领书 1 套
19.8 钥匙 门用 2 个
20. 安全功能
功能 目的 动作内容
1 控制回路1 过电流?；??；ど璞?a
2 系统异常 ?；ど璞?b
3 逆转防止继电器 ?；ど璞?b
4 温度保险丝 ?；ど璞?b
5 送风机温度开关 ?；ど璞?b
6 送风机短路?；げＡЧ鼙Ｏ账??；ど璞?b
7 温度过升防止器 ?；な匝?b
8 室温补偿断线ト检出回路 ?；ど璞?b
9 干球温度断线检出回路 ?；ど璞?B
10 试样温度断线检出回路（仅在试样温度控制中） ?；ど璞?B
11 冷凝器风扇短路?；??；ど璞?B
12 冷凝器风扇过负载?；??；ど璞?B
13 压缩机1 温度传感器断线检出回路 ?；ど璞?b
14 压缩机1 短路?；??；ど璞?b
15 压缩机1 过电流?；??；ど璞?b
16 压缩机1 吐出管温度开关 ?；ど璞?b
17 压缩机1 高低压压力开关 ?；ど璞?b
18 压缩机1 结霜检出回路 ?；ど璞?b
19 压缩机1 回路温度范围外 ?；ど璞?b
20 加热器?加湿器过电流?；??；ど璞?b
21 控制回路2 过电流?；??；ど璞?b
22 控制回路短路?；げＡЧ鼙Ｏ账??；ど璞?b
23 温度上下限报警功能 （内置于温湿度调节器） ?；な匝?b
24 湿球温度断线检出回路 ?；ど璞?c
25 加湿器空烧防止器 ?；ど璞?c
26 加湿器水位检测 ?；ど璞?c
27 温度上限偏差报警功能（内置于温湿度调节器） ?；な匝?d
28 湿度上下限报警功能 （内置于温湿度调节器） ?；な匝?d
29 供水箱缺水开关 ?；ど璞?e
30 门开关 ?；と嗽?f
功能 目的 动作内容
31 纱布干燥检出 ?；ど璞?g
32 供水箱低水位开关 ?；ど璞?g
33 试样电源控制端子 ?；な匝?h
a ： 整个设备停止。
b ： 显示警报，报警蜂鸣器发出声响。设备停止运行。
c ： 显示警报，报警蜂鸣器发出声响。 。
备份运行OFF 时，设备停止运行。
备份运行ON 时，设备继续温度运行。
d ： 显示警报， 报警蜂鸣器发出声响。设备进行所定的安全动作。
e ： 显示警报，报警蜂鸣器发出声响。设备继续温度运行。
f ： 显示警报，报警蜂鸣器发出声响。
暂停动作OFF 时，设备继续运行。
暂停动作ON 时，设备暂停运行。
报警显示、报警蜂鸣器可选择ON/OFF。
g ： 显示警报，报警蜂鸣器发出声响。设备继续运行。
h ： 设备运行停止或运行停止的安全装置动作时，停止对试样的供电。
21. 供水
21.1 供水方式 供水泵供水
21.2 水箱安装位置
机械室正面
21.3 水箱容量 40L（固定式水箱 20L×2 个）
21.4 自动供水口 口径：Rc3/8(后部)
21.5 水质 导电率：0.1～10μS/㎝
6～7pH 的纯水
21.6 供水压力 0.01MPa～0.05MPa
22. 试样的限制 以下物质不得用于试验。
? 爆炸性物质，可燃性物质及含有该类物质的物质
? 具有腐蚀性的物质
? 生物
? 超过容许发热负荷的物质
23. 除外项目
? 搬入?安装场地的准备工程
? 一次电源工程
? 供排水工程

系列产品技术规格参数指标

爱斯佩克ESPEC高低温湿热试验箱ARL-0680-AE，ARL-1100-AE   Model ARL−0680 ARL−1100  Model ARS−0220 ARS−0390 ARS−0680 ARS−1100   Model ARU−0680 ARU−1100   Model ARG−0220 ARG−0390 ARG−0680 ARG−1100   (ARS-0680/1100, ARG-0680/1100)
AR series has big allowable heat loads generated by the specimen,
and achieves improved temperature change rate in an expanded temperature and humidity range.
The new N-instrumentation allows AR series chambers to support easy-to-use networking system.
ESPEC offers two temperature control ranges: −75℃ to ＋180℃ or −45℃ to ＋180℃ ,
with or without humidity control (10 to 98％rh).
These models incorporate the most desirable features in temperature and humidity chambers.
ARS−0220
*Viewing window is optional.
ARS−1100
Advanced reliability
Environmental Stress Chambers
1
2
Superior temperature heating
and cooling control
at 3℃ /min. with specimen load
Temperat ure heating and cooling
performance at 4 to 6℃ /min. (no load),
and can handle temperature cycle tests at
3℃ /min. (with load*)
* ARS-1100 specimen: aluminum 38kg
(including shelf 12kg)
Highly uniform temperature
distribution
Highly uniform temperature distribution
minimizes variations in test results.
Reduced temperature and
humidity stabilization time
Temperature and humidity stabilization
time is greatly reduced by minimizing
hunting as the chamber approaches setpoint. (under testing operation from RT
to 85℃ /85％ rh).
Wider control range for
temperature and humidity
Features a wider control range of
temperature and humidity, including
stable control at 95℃ /98％ rh.
Meets international standards
D e sig ne d t o c omply w it h m ajor
environmental test standards such as
IEC60068-2, or ISO16750-4 (5.3).
(Refer to compatible test standards)
International safety standard
compliance
Complies with Safety of Machinery
(ISO 12100), Low Voltage (IEC 60204),
EMC (IEC 61000-6-2, IEC 61000-6-4).
Temperature (℃)
100
90
98
80
70
60
50
40
30
20
10
10 20 30 40 50 60 70 80
95
90 100
0
Relative
Humidity
(%rh)
ARS?ARL
PR?PL?PSL
＊Continuous operation at or below ＋40℃ is limited because of frost formation on the cooler
and dehumidifier.
Temperature & Humidity Control Range
(ambient temperature at ＋20℃ with no load)
Characteristics
● Compatible Test Standards
?IEC60068-2-1: Cold
?IEC60068-2-2: Dry heat
?IEC60068-2-3: Damp heat, steady state
?IEC60068-2-14 Nb: Change of temperature with
specified rate of change *
?IEC60068-2-38: Composite temperature/ humidity
cyclic test *
?IEC60068-2-78: Damp heat, steady state
?ISO16750-4 5.3: Temperature cycling
Model Heat up (K/min.) Pull down (K/min.)
ARL/ARU−0680 6.3 4.8
ARL/ARU−1100 4.7 4.4
ARS/ARG−0220 6.0 5.2
ARS/ARG−0390 5.0 4.0
ARS/ARG−0680 6.0 4.2
ARS/ARG−1100 4.7 4.1
Temperature change rate
＊At ambient temperature, ＋20℃ no specimen.
Safety precautions
● Do not use specimens which are explosive or flammable, or which
contain such substances.

Supports heat loads
up to 4500W*
(During temperature testing)
Supports electrically-charged specimens,
and can compensate up to 4500W of
heat load during temperature testing,
depending on the chamber model (500W
during temperature and humidity
testing).
* Test area temperature:+20℃
User-friendly features
Standard features include cable ports on
both sides which allow free access of
the test area. Antirust and oil proof 18-8
Cr-Ni stainless steel plate is used as
external panels. It is possible to select
water supply via water tank or direct
water coupling alliteratively all the
time.
Chamber restricted to
lock the door
It is now possible to lock the chamber
door to prevent accidental operation of
the chamber during testing.
The handle part design has also been
improved so the door closing is easier
and safer.
New refrigeration circuit and
     condenser filter improves
reliability
Thanks to newly designed refrigeration
circuit, reliability is improved. And
further more condenser filter, prevents a
condenser fan from clogging becomes
standard equipment.
Cable ports on both walls
Water tank Key
Characteristics
4
Controller N-instrumentation
N-instrumentation equipped
with a color LCD touch panel
Wide 7-inch screen with LED backlight
is clearer and provides faster display
speed.
Interior light button
It is able to switch ON/OFF from the
interior light button any time.
Information button
When there are some things need to be
notified to the operator, information
button will alart to the operator. By
pressing the button, you will find
notifications such as "Check Humidity
Tray".
Trend graph output on
USB memory
Trend graphs can be displayed on the
web application or downloaded on USB
m e m o r y. I t i s a l s o p o s s i b l e t o
continuously register data on USB
memory if numerous data records are
needed.
N-instrumentation
USB memory port
Touch icon to show
navigation bar.
Touch navigation
Interior light
Display TFT Color LCD (7.0inch)
Operating mode Constant operation, Program operation, Remote operation, Stop
Setting range
● Constant setup: 3 patterns
Setting range: Temp.: −80.0℃ to ＋185.0℃ , 0.1℃ unit (ARS, ARG)
Temp.: −50.0℃ to ＋185.0℃ , 0.1℃ unit (ARL, ARU)
Humidity: 0 to 100％ rh, 1％ unit (ARS, ARL)
● Program setup: 40 patterns (99 steps)
Setting range: Temp.: −80.0℃ to ＋185.0℃ , 0.1℃ unit (ARS, ARG)
−50.0℃ to ＋185.0℃ , 0.1℃ unit (ARL, ARU)
Humidity: 0 to 100％ rh, 1％ unit
Time: 0 hour and 1 min. to
9999 hours and 59 min. 1 min. unit
Language Japanese, English, Chinese (simplified, traditional), Korean
Interface USB 2.0 standard compliant (A-type connector)
External memory
function
Write sampling data, Read/ Write program, Backtrace output,
Add-on/system updates
Network function Interface: Ethernet port (100base-TX)
Web function Monitoring, setting, operation, Data Record Function,
maintenance setting, alert
Browser Windows Internet Explorer10
Application of USB MEMORY
Continous record test data
Data transfer
Copy test program
5
Network
Remote monitoring and control
(Ethernet connection)
A unique web application allows the
user to monitor the chamber, set
programs, and start and stop operation
from a PC connected to the chamber
Ethernet port (LAN’s port). No software
required, the chamber can be accessed
and controlled from PC via a web
browser (Smartphone, tablets and the
like can also be used).
Wireless connection and multiple units
connection are also possible.
alert
When an alarm is triggered, an is
sent to the registered PC or
address. A notification can also be sent
at the time of test completion.
*Requires an intranet environment capable of
sending s.
Multilingual display
The language available for the Web
application (Japanese/ English/ Simplified
Chinese/ Traditional Chinese/ Korean)
can be changed without affecting the
N-instrumentation language display.
Remote monitoring and control thanks to a Web application
Ethernet
無線LANによる接続例
内蔵ワイヤレスダイレクトによる接続例
Program copy and computer editing
携帯
スマートフォン
タブレットコントローラー
（オプション）
PC
Edit
Copy
小型環境試験器
（Wi-Fi機能搭載）
Wi-Fiルーター
（オプション）
スマートフォン
スマートフォン
小型環境試験器
小型環境試験器
ワイヤレスダイレクト
（オプション）
Program copy and computer editing
Edit
Copy
AR series
Ethernet
Network
Wi-Fi router
Smartphone Tablet controller
PC
Ethernet
phone
Smartphone
Mail server
Intranet
(company LAN)
alert
PC
AR series
Environmental
Stress Chamber
● Program editing ● Graph display
Image
Screen
Privileges Chamber monitor Constant Mode/ Program Setup Run/ Stop configuration Device
Administrator ○ ○ ○ ○
Operator ○ ○ ○ ×
User ○ × × ×
Login information
○= available; ×= Not available
6
Network
エスペック ネットワーク 検 索
エスペック オンライン 検 索
試験棟
集中管理システム （旧：Web統合管理システム）（別売）
100台までの試験器の状態を１画面で確認することができる
集中管理システムに接続可能です。
Ethernet
ハイパワー恒温（恒湿）器
ネットワークアダプター
旧：RS-485
LANコンバーター
Ethernet
プラチナスKシリーズ
事務棟
Ethernet
Ethernet
集中管理システム
クライアントPC
イントラネット
2015年3月対応予定
Lab
Web Integrated Network (Sold separay)
Maximum 100units of connected chambers and other peripherals necessary
for environmental testing are manned via Internet.
Ethernet
AR series
LAN converter
Ethernet
Platinous K Series
Office
Ethernet
Ethernet
Web integrated
network system
Client PC
Intranet
Access to video
Copy and reproduce testing
Thanks to the USB memory you can
copy the same test program in multiple
chambers, provided that they have the
same operation range. No need to
program each chamber, just connect the
USB and the test can start.
Download edit programs online
Via the Pattern Manager Lite software
installed on your PC, edit programs
according to your testing needs, and
upload them with a USB.
Edit programs
Through our online website Test Navi,
dedicated to reliability and testing
information, you can find most of the
recognized international standard,
available for download.
Charge them as is on your USB memory,
or edit them and transfer to your chamber.
* Test Navi is a website dedicated to reliability
testing information and technologies. http://
www.test-navi。。ｃｏｍ/eng/index.html
The Pattern Manager Lite software allows
you to edit programs for your chamber,
view and edit data as graph, etc.
The software can be downloaded from the
Test Navi website.
製品会員専用サイト
パターンマネージャーの情報、
WEBマネージャー情報のダウンロード
環境試験規格一覧
パターンマネージャーLite対応
試験条件プログラムパターンダウンロード
ダウンロード
試験規格プログラムパターン
ファイルの活用方法
活用方法をムービーでご覧いただけます。 ムービー
Product registration
membership Website
Download Pattern Manager and
WEB Manager information.
Environmental Test
Standards
For Pattern Manager Lite
Test methods download
Download
Product Registration
Membership Website
製品会員専用サイト
パターンマネージャーの情報、
WEBマネージャー情報のダウンロード
環境試験規格一覧
パターンマネージャーLite対応
試験条件プログラムパターンダウンロード
ダウンロード
試験規格プログラムパターン
ファイルの活用方法
活用方法をムービーでご覧いただけます。 ムービー
Product registration
membership Website
Download Pattern Manager and
WEB Manager information.
Environmental Test
Standards
For Pattern Manager Lite
Test methods download
Download
Product Registration
Membership Website
● Test Navi
(http://www.test-navi。。ｃｏｍ/eng/index.html)
This website provides practical knowledge on environmental testing
that ESPEC has acquired through years of experience, as well as
covering everything from the fundamentals to the latest information on
environmental and reliability testing.
? Updates for chamber controller software
? Search for environmental test standards
? Download test profiles from a list of environmental test standards
Ethernet
無線LANによる接続例
内蔵ワイヤレスダイレクトによる接続例
Program copy and computer editing
携帯
スマートフォン
タブレットコントローラー
（オプション）
PC
Edit
Copy
小型環境試験器
（Wi-Fi機能搭載）
Wi-Fiルーター
（オプション）
スマートフォン
スマートフォン
小型環境試験器
小型環境試験器
ワイヤレスダイレクト
（オプション）
Program copy and computer editing
Edit
Copy
AR series
Ethernet
Network
Wi-Fi router
Smartphone Tablet controller
PC
Ethernet
phone
Smartphone
Mail server
Intranet
(company LAN)
alert
PC
AR series
Environmental
Stress Chamber
7
TEMPERATURE & HUMIDITY CHAMBER
ARL −45 to ＋180℃?10 to 98％rh

爱斯佩克ESPEC高低温湿热试验箱Model ARL−0680 ARL−1100 
System Balanced Temperature & Humidity Control (BTHC) system
Temp. performance *1
Temp. range −45 to ＋180℃ (−49 to ＋356℉ )
Temp. fluctuation ±0.3K
Temp. variation in space 3.0K
Temp. rate
of change *2
Heat up rate 6.3 K/min. 4.7 K/min.
Pull down rate 4.8 K/min. 4.4 K/min.
Max. allowable heat load 4500 W Test area temperature: ＋20℃
Temp. & humid.
performance *1
Temp. & humid. range ＋10 to ＋95℃ / 10 to 98％rh
Humid. fluctuation ±2.5%rh
Max. allowable heat load 500 W Test area conditions: ＋85℃ /85%rh
Construction
Exterior material 18 Cr-stainless steel plate (Hairline finish)
Test area material 18-8 Cr-Ni Stainless steel plate (BA finish)
Insulation Foamed phenol, glass wool
Heater Nichrome strip wire heater (3 kW×2)
Humidifier Sheathed heater
Cooler Plate fin cooler and dehumidifier
Refrigeration unit
System Mechanical single-stage refrigeration system
Refrigerator Scroll-type compressor
Refrigerator capacity 3.0 kw 3.75 kw
Expansion mechanism Electronic expansion valve
Refrigerant R404A
Air circulator Sirocco fan
Interface Ethernet
Fittings 100mm cable port (×2), specimen power supply control terminal, condenser filter,
specimen temperature input terminal, time signal (×2), casters with levelling feet (×4)
Capacity 680 L 1100 L
Chamber total load resistance 80 kg 150 kg
Inside dimensions mm (inch) *3 W850×H1000×D800 (W33.5×H39.4×D31.5) W1100×H1000×D1000 (W43.3×H39.4×D39.4)
Outside dimensions mm (inch) *3 W1050×H1955×D1805 (W41.3×H77.0×D71.1) W1300×H1955×D2005 (W51.2×H77.0×D78.9)
Weight 510 kg 600 kg
Utility requirements
Allowable ambient conditions 0 to ＋40℃ (＋32 to ＋104℉ ) / 75%rh max.
Power
supply *4
200V AC 3φ50/60Hz 53 A 56 A
220V AC 3φ60Hz 49 A 52 A
380V AC 3φ50Hz 23 A 25 A
400V AC 3φ50Hz *5 22 A 23 A
Noise level *6 61 dB 62 dB
Exhaust heat quantity kJ/h (kcal/h) 32400 (7743) 39600 (9464)
*1: At ambient temperature +20℃ , no specimen. Performance shown above conforms to IEC 60068-3-5:2001 and IEC 60068-3-6:2001.
*2: Temperature rate of change in the temperature range excluding ±10% of max/min. temperature.
*3: Excluding protrusions.
*4: Power supply voltage fluctuation to be ±10% of rated value.
*5: Conforms to CE marking based on EU directives.
*6: Measurements are to be taken in an anechoic room at a height of 1.2m from the floor and a distance of 1m from the chamber front panel
(ISO 1996-1:2003 _ A-weighted sound pressure level).
8
TEMPERATURE & HUMIDITY CHAMBER
ARS −75 to ＋180℃?10 to 98％rh

爱斯佩克ESPEC高低温湿热试验箱Model ARS−0220 ARS−0390 ARS−0680 ARS−1100 
System Balanced Temperature & Humidity Control (BTHC) system
Temp. performance *1
Temp. range −75 to ＋180℃ (−103 to ＋356℉ )
Temp. fluctuation ±0.3K
Temp. variation in space 3.0K
Temp. rate
of change *2
Heat up rate 6.0 K/min. 5.0 K/min. 6.0 K/min. 4.7K/min.
Pull down rate 5.2 K/min. 4.0 K/min. 4.2 K/min. 4.1K/min.
Max. allowable heat load Test area temperature: ＋20℃
3000 W 4500 W
Temp. & humid.
performance *1
Temp. & humid. range ＋10 to ＋95℃ / 10 to 98％rh
Humid. fluctuation ±2.5%rh
Max. allowable heat load Test area conditions: ＋25 to ＋95℃ /90%rh Test area conditions: ＋85℃ /85%rh
350 W 300 W 500 W
Construction
Exterior material 18 Cr-stainless steel plate (Hairline finish)
Test area material 18-8 Cr-Ni Stainless steel plate (BA finish)
Insulation Foamed phenol, glass wool
Heater Nichrome strip wire heater
(1.75 kW×2) (3 kW×2)
Humidifier Sheathed heater
Cooler Plate fin cooler and dehumidifier
Refrigeration unit
System Mechanical cascade and compression refrigeration system
Refrigerator Rotary compressor Scroll compressor
Refrigerator capacity Unit 1: 2.2 kw ×1,
Unit 2: 2.2 kw ×1
Unit 1: 3.0 kw ×1,
Unit 2: 3.0 kw ×1
Unit 1: 3.75 kw ×1,
Unit 2: 3.75 kw ×1
Expansion mechanism Electronic expansion valve
Refrigerant R404A, R508A R404A, R23
Air circulator Sirocco fan
Interface Ethernet
Fittings 100mm cable port (×2), specimen power supply control terminal, condenser filter,
specimen temperature input terminal, time signal (×2), casters with levelling feet (×4)
Capacity 220 L 390 L 680 L 1100 L
Chamber total load resistance 50 kg 80 kg 80 kg 150 kg
Inside dimensions mm (inch) *3 W700×H800×D400
(W27.6×H31.5×D15.8)
W700×H800×D700
(W27.6×H31.5×D27.6)
W850×H1000×D800
(W33.5×H39.4×D31.5)
W1100×H1000×D1000
(W43.3×H39.4×D39.4)
Outside dimensions mm (inch) *3 W900×H1742×D1455
(W35.4×H68.6×D57.3)
W900×H1742×D1705
(W35.4×H68.6×D67.1)
W1050×H1955×D1805
(W41.3×H77.0×D71.1)
W1300×H1955×D2005
(W51.2×H77.0×D78.9)
Weight 390 kg 405 kg 615 kg 700 kg
Utility requirements
Allowable ambient conditions 0 to ＋40℃ (＋32 to ＋104℉ ) / 75%rh max.
Power
supply *4
200V AC 3φ50/60Hz ─ ─ 63 A 70 A
220V AC 3φ60Hz 38 A *5 38 A *5 58 A 64 A
380V AC 3φ50Hz 24 A *5 24 A *5 28 A 32 A
400V AC 3φ50Hz *5 23 A 23 A 27 A 29 A
Noise level *6 57 dB 58 dB 62 dB 63 dB
Exhaust heat quantity kJ/h (kcal/h) 26600 (6357) 26600 (6357) 39600 (9464) 46800 (11185)
*1: At ambient temperature +20℃ , no specimen. Performance shown above conforms to IEC 60068-3-5:2001 and IEC 60068-3-6:2001.
*2: Temperature rate of change in the temperature range excluding ±10% of max/min. temperature.
*3: Excluding protrusions.
*4: Power supply voltage fluctuation to be ±10% of rated value.
*5: Conforms to CE marking based on EU directives.
*6: Measurements are to be taken in an anechoic room at a height of 1.2m from the floor and a distance of 1m from the chamber front panel
(ISO 1996-1:2003 _ A-weighted sound pressure level).
9

爱斯佩克ESPEC高低温湿热试验箱Model ARU−0680 ARU−1100  
System Balanced Temperature Control (BTC) system
Temp. performance *1
Temp. range −45 to ＋180℃ (−49 to ＋356℉ )
Temp. fluctuation ±0.3 K
Temp. variation in space 3.0 K
Temp. rate
of change *2
Heat up rate 6.3 K/min. 4.7 K/min.
Pull down rate 4.8 K/min. 4.4 K/min.
Max. allowable heat load 4500 W Test area temperature: ＋20℃
Construction
Exterior material 18 Cr-stainless steel plate (Hairline finish)
Test area material 18-8 Cr-Ni Stainless steel plate (BA finish)
Insulation Foamed phenol, glass wool
Heater Nichrome strip wire heater (3kW ×2)
Cooler Plate fin cooler
Refrigeration unit
System Mechanical single-stage refrigeration system
Refrigerator Scroll-type compressor
Refrigerator capacity 3.0 kw 3.75 kw
Expansion mechanism Electronic expansion valve
Refrigerant R404A
Air circulator Sirocco fan
Interface Ethernet
Fittings 100mm cable port (×2), specimen power supply control terminal, condenser filter,
specimen temperature input terminal, time signal (×2), casters with levelling feet (×4)
Capacity 680 L 1100 L
Chamber total load resistance 80 kg 150 kg
Inside dimensions mm (inch) *3 W850×H1000×D800 (W33.5×H39.4×D31.5) W1100×H1000×D1000 (W43.3×H39.4×D39.4)
Outside dimensions mm (inch) *3 W1050×H1955×D1805 (W41.3×H77.0×D71.1) W1300×H1955×D2005 (W51.2×H77.0×D78.9)
Weight 505 kg 595 kg
Utility requirements
Allowable ambient conditions 0 to ＋40℃ (＋32 to ＋104℉ ) / 75%rh max.
Power
supply *4
200V AC 3φ50/60Hz 53 A 56 A
220V AC 3φ60Hz 49 A 52 A
380V AC 3φ50Hz 23 A 25 A
400V AC 3φ50Hz *5 22 A 23 A
Noise level *6 61 dB 62 dB
Exhaust heat quantity kJ/h (kcal/h) 32400 (7743) 39600 (9464)
TEMPERATURE CHAMBER
ARU −45 to ＋180℃
*1: At ambient temperature +20℃ , no specimen. Performance shown above conforms to IEC 60068-3-5:2001.
*2: Temperature rate of change in the temperature range excluding ±10% of max/min. temperature.
*3: Excluding protrusions.
*4: Power supply voltage fluctuation to be ±10% of rated value.
*5: Conforms to CE marking based on EU directives.
*6: Measurements are to be taken in an anechoic room at a height of 1.2m from the floor and a distance of 1m from the chamber front panel
(ISO 1996-1:2003 _ A-weighted sound pressure level).
10

爱斯佩克ESPEC高低温湿热试验箱Model ARG−0220 ARG−0390 ARG−0680 ARG−1100  
System Balanced Temperature Control (BTC) system
Temp. performance *1
Temp. range −75 to ＋180℃ (−103 to ＋356℉ )
Temp. fluctuation ±0.3 K
Temp. variation in space 3.0 K
Temp. rate
of change *2
Heat up rate 6.0 K/min. 5.0 K/min. 6.0 K/min. 4.7K/min.
Pull down rate 5.2 K/min. 4.0 K/min. 4.2 K/min. 4.1K/min.
Max. allowable heat load
Test area temperature: ＋20℃
3000 W 4500 W
Construction
Exterior material 18 Cr-stainless steel plate (Hairline finish)
Test area material 18-8 Cr-Ni Stainless steel plate (BA finish)
Insulation Foamed phenol, glass wool
Heater
Nichrome strip wire heater
(1.75 kW×2) (3 kW×2)
Cooler Plate fin cooler
Refrigeration unit
System Mechanical cascade refrigeration system
Refrigerator Scroll-type compressor
Refrigerator capacity Unit 1: 2.2 kw ×1,
Unit 2: 2.2 kw ×1
Unit 1: 3.0 kw ×1,
Unit 2: 3.0 kw ×1
Unit 1: 3.75 kw ×1,
Unit 2: 3.75 kw ×1
Expansion mechanism Electronic expansion valve
Refrigerant R404A, R508A R404A, R23
Air circulator Sirocco fan
Interface Ethernet
Fittings 100mm cable port (×2), specimen power supply control terminal, condenser filter,
specimen temperature input terminal, time signal (×2), casters with levelling feet (×4)
Capacity 220 L 390 L 680 L 1100 L
Chamber total load resistance 50 kg 80 kg 80 kg 150 kg
Inside dimensions mm (inch) *3 W700×H800×D400
(W27.6×H31.5×D15.8)
W700×H800×D700
(W27.6×H31.5×D27.6)
W850×H1000×D800
(W33.5×H39.4×D31.5)
W1100×H1000×D1000
(W43.3×H39.4×D39.4)
Outside dimensions mm (inch) *3 W900×H1742×D1455
(W35.4×H68.6×D57.3)
W900×H1742×D1705
(W35.4×H68.6×D67.1)
W1050×H1955×D1805
(W41.3×H77.0×D71.1)
W1300×H1955×D2005
(W51.2×H77.0×D78.9)
Weight 385 kg 400 kg 615 kg 700 kg
Utility requirements
Allowable ambient conditions 0 to ＋40℃ (＋32 to ＋104℉ ) / 75%rh max.
Power
supply *4
200V AC 3φ50/60Hz ─ ─ 63 A 70 A
220V AC 3φ60Hz 38 A *5 38 A *5 58 A 64 A
380V AC 3φ50Hz 24 A *5 24 A *5 28 A 32 A
400V AC 3φ50Hz *5 23 A 23 A 27 A 29 A
Noise level *6 57 dB 58 dB 62 dB 63 dB
Exhaust heat quantity kJ/h (kcal/h) 26600 (6357) 26600 (6357) 39600 (9464) 46800 (11185)
TEMPERATURE CHAMBER
ARG −75 to ＋180℃
*1: At ambient temperature +20℃ , no specimen. Performance shown above conforms to IEC 60068-3-5:2001.
*2: Temperature rate of change in the temperature range excluding ±10% of max/min. temperature.
*3: Excluding protrusions.
*4: Power supply voltage fluctuation to be ±10% of rated value.
*5: Conforms to CE marking based on EU directives.
*6: Measurements are to be taken in an anechoic room at a height of 1.2m from the floor and a distance of 1m from the chamber front panel
(ISO 1996-1:2003 _ A-weighted sound pressure level).
11
Model 0220 0390 0680 1100
Shelf size (mm) W667
D350
W667
D650
W817
D750
W1067
D950
Shelf weight 2 kg 3 kg 6 kg 12 kg
Shelf load capacity
(evenly distributed load) 30 kg 30 kg 40 kg 50 kg
Shelf support max. load
(Including shelf weight) 50 kg 80 kg 80 kg 100 kg
● Control circuit overcurrent protection
● Control circuit short circuit protection cartridge fuse
● System error
● Reverse-prevention relay
● Thermal fuse
● Temperature switch for air circulator
● Air circulator short circuit protection
● Ambient temperature input burn-out detection circuit
● Dry-bulb temperature input burn-out detection circuit
● Specimen temperature input burn-out detection circuit
(only when using specimen temperature control)
● Condenser fan short circuit protection
● Condenser fan overload protection
● Refrigerator temperature sensor burned detect circuit
● Refrigerator short circuit protection
● Refrigerator overcurrent protection
● Refrigerator discharge pipe temperature switch (0680/1100)
● Refrigerator high (low) pressure switch
● Refrigerator frost detection cicuit (0680/1100)
● Refrigerator circuit temperature range over
● Refrigerator frost trouble detection temperature switch
(ARS-0680/1100, ARG-0680/1100)
● Refrigerator discharge pipe temperature trouble detection circuit
(ARS, ARG)
● Heater (humidifier) leak current protection
● Wet bulb temperature input burnout detection circuit
(ARL, ARS)
● Humidifier boil-dry protector (ARL, ARS)
● Humidifier water level detector (ARL, ARS)
● Water tank empty switch (ARL, ARS)
● Water tank low level switch (ARL, ARS)
● Dry wick detection (ARL, ARS)
● Overheat protector
● High deviation temperature alarm
(built into temperature and humidity controller)
● High/ low absolute temperature (humidity) alarms
(built into temperature and humidity controller)
● Specimen power supply control terminal
● Chamber door switch
ACCESSORIES SAFETY DEVICES
SHELVES SIZE AND LOAD RESISTANCE
● Cable port rubber plug (φ100 mm) 2 each
● Shelf brackets 1 set
stainless steel plate (18-8 Cr-Ni stainless steel)
● Shelf 1
stainless steel wire (18-8 Cr-Ni stainless steel)
● Door key 2
● Cartridge fuse (Class B, 250 V 0.4 A, 5 A, 8 A)     1 each
● Wet-bulb wick (ARL, ARS) 1 box (24 wicks)
● Specimen temperature measuring thermocouple (type T, 3m) 1
● Specimen temperature input connector 1
● Operation manual 1
12
OPTIONS
UTILITY TEST SAMPLE SETTING OBSERVATION
Additional cable port
Provided in addition / replacement of
the standard cable ports.
?50 mm diameter
?100 mm diameter
* Each cable port is equipped with a silicone
sponge rubber plug.
Cable port rubber plug
Prevents air leakage from the cable
port.
Portable tank
Power cable
Used to refill the standard tank.
*ARS, ARL only
?2.5 m
?5 m
?10m
*The chamber does not come with a power cable.
Water purifier (WS-1)
Water purifier with reverse osmosis
membrane. Produces approx 6.6L per
hour (at primary water temp. ＋10℃ ).
Shelf, shelf bracket
Equivalent to standard accessory.
Heavy-duty shelf
Us e d t o hold he av y s p e c i me n s
exceeding the load capacity of the
standard shelf.
Load capacity: 50kg (max. 2 shelves)
*Standard for 1100L model
Viewing window
Used for observation of the specimens
inside the chamber.
Dimensions: W340×H440 mm
NETWORK
Communication cables
?RS-485 5m/ 10m/ 30m
?RS-232C 1.5m/ 3m/ 6m
?GPIB 2m/ 4m
Interface
Computer interface
?RS-485
?GPIB
?RS-232C
Water leak detection system and
dew tray to catch dripping water
are also available to detect and
prevent water damages.
OPTIONS
13
Temperature recorder (digital)
Portable type
−100 to ＋200℃ 6 dots
Temperature and humidity recorder (digital)
Portable type
−100 to ＋200℃ / 0 to 100%rh 6 dots
Temperature sensor terminal
Terminal board for dry-bulb temperature sensor in the chamber.
DC output terminal
Outputs temperature, humidity, and
temperature of the specimen from the
test area.
Relay contact output
Up to 8 contacts can be added to the
standard 2 relay contacts (time signals).
Paperless recorder - portable type
Records temperature of each section
such as the temperature inside the
chamber.
Data saving cycle: 5 sec.
External recording media:
CF memory card (256MB)
USB port
Language support: ENG, JPN
[Temperature type]
Temperature range: −100 to ＋200℃
Number of inputs: Temperature 1
(5 more channels can be turned ON)
[Temperature and humidity type]
Temperature range: −100 to ＋200℃
Humidity range: 0 to 100％rh
Number of inputs:
Temperature 1 / Humidity 1
(4 more channels can be turned ON)
OPTION
OPTION
OPTION
OPTION
MODE
MODE
SPECIMEN
TEMPERATURE INPUT
(TYPE T)
試料温度入力
(JIS T)
POWER SUPPLY
CONTROL
FOR SPECIMEN

No.2
試料電源制御出力
タイムシグナル出力
TIME SIGNALS
ETHERNET
No.6
No.7
No.8
0
No.9
タイムシグナル出力
TIME SIGNALS
外部警報出力
EXTERNAL ALARM
SIGNAL
No.3
No.5
No.4
EXTRA OVERHEAT
PROTECTOR
追加温度過昇防止器
OVERCOOL PROTECTOR
温度過冷防止器
槽内温度
(JIS T)
モニタ出力 (DC1-5V リニア)
CHAMBER TEMPERATURE
(TYPE T)
MONITOR OUTPUT
(1-5V DC LINEAR)
記録計用出力
RECORDER OUTPUT
OFF
OPTION
OPTION
OPTION
OPTION
MODE
MODE
SPECIMEN
TEMPERATURE INPUT
(TYPE T)
試料温度入力
(JIS T)
POWER SUPPLY
CONTROL
FOR SPECIMEN

No.2
試料電源制御出力
タイムシグナル出力
TIME SIGNALS
ETHERNET
No.6
No.7
No.8
0
No.9
タイムシグナル出力
TIME SIGNALS
外部警報出力
EXTERNAL ALARM
SIGNAL
No.3
No.5
No.4
EXTRA OVERHEAT
PROTECTOR
追加温度過昇防止器
OVERCOOL PROTECTOR
温度過冷防止器
槽内温度
(JIS T)
モニタ出力 (DC1-5V リニア)
CHAMBER TEMPERATURE
(TYPE T)
MONITOR OUTPUT
(1-5V DC LINEAR)
記録計用出力
RECORDER OUTPUT
OFF
LOGGING TEST QUALITY
Humidifier delay control
To protect specimens from condensation, humidity control starts after
temperature reaches the set value.
*ARL, ARS only
OPTIONS
Operation manual
Reports & certificates
?CD
?Booklet
?Testing and inspection report
?Test data
?Temperature (& humidity) uniformity
measurement
?Calibration report
?Calibration certificate
?Traceability system chart
?Traceability certificate
Additional overheat protector
Additional preventive measures can be
taken for excessive temperature rise in
the chamber, in addition to the standard
equipped overheat protector.
Overcool protector
If the temperature inside the chamber
decreases excessively, the chamber
stops operating to prevent the specimens from being damaged.
Trouble buzzer
If a trouble occurs, the buzzer will alert
you of the situation.
Rotating signal lamp
The lamp lights up when alarm triggers.
(Available in red or yellow)
External alarm terminal
If the safety device of the chamber is
activated, the external alarm terminal
will notify it to a remote point.
Emergency stop switch
Stops the chamber immediay.
14
Safety precautions
● Do not use specimens which are explosive or flammable,
or which contain such substances.
To do so could be hazardous, as this may lead to fire or
explosion.
● Do not place corrosive materials in the chamber.
If corrosive substances or liquid is used, the life of the unit
may be significantly shortened specifically because of the
corrosion of stainless steel, resin and silicone materials.
● Do not use living organisms or items that exceed the
allowable heat load as a specimen.
● Be sure to read the operation manual before operation.
Safety precautions
● Do not use specimens which are explosive or flammable, or which contain such
substances.
To do so could be hazardous, as this may lead to fire or explosion.
● Do not place corrosive materials in the chamber.
If corrosive substances or liquid is used, the life of the unit may be significantly
shortened specifically because of the corrosion of stainless steel, resin and silicone
materials.
● Do not use living organisms or items that exceed the allowable heat load as a
specimen.
● Be sure to read the operation manual before operation.
Safety precautions
● Do not use specimens which are explosive or flammable, or which
contain such substances.
To do so could be hazardous, as this may lead to fire or explosion.
● Do not place corrosive materials in the chamber.
If corrosive substances or liquid is used, the life of the unit may be
significantly shortened specifically because of the corrosion of stainless
steel, resin and silicone materials.
● Do not use living organisms or items that exceed the allowable heat
load as a specimen.
● Be sure to read the operation manual before operation.
Please contact us for non-standard specification.
Please contact us for non-standard specification.
Please contact us for non-standard specification.
200V AC, 220V AC spec. 380V AC, 400V AC spec.
OPTION
OPTION
OPTION
OPTION
MODE
MODE
SPECIMEN
TEMPERATURE INPUT
(TYPE T)
試料温度入力
(JIS T)
POWER SUPPLY
CONTROL
FOR SPECIMEN

No.2
試料電源制御出力
タイムシグナル出力
TIME SIGNALS
ETHERNET
No.6
No.7
No.8
0
No.9
タイムシグナル出力
TIME SIGNALS
外部警報出力
EXTERNAL ALARM
SIGNAL
No.3
No.5
No.4
EXTRA OVERHEAT
PROTECTOR
追加温度過昇防止器
OVERCOOL PROTECTOR
温度過冷防止器
槽内温度
(JIS T
)
モニタ出力 (DC1
-5V リニア)
CHAMBER TEMPERATURE
(TYPE T)
MONITOR OUTPUT
(1-5V DC LINEA
R)
記録計用出力
RECORDER OUTPUT
OFF
OPTION
OPTION
OPTION
OPTION
MODE
MODE
SPECIMEN
TEMPERATURE INPUT
(TYPE T)
試料温度入力
(JIS T)
POWER SUPPLY
CONTROL
FOR SPECIMEN

No.2
試料電源制御出力
タイムシグナル出力
TIME SIGNALS
ETHERNET
No.6
No.7
No.8
0
No.9
タイムシグナル出力
TIME SIGNALS
外部警報出力
EXTERNAL ALARM
SIGNAL
No.3
No.5
No.4
EXTRA OVERHEAT
PROTECTOR
追加温度過昇防止器
OVERCOOL PROTECTOR
温度過冷防止器
槽内温度
(JIS T)
モニタ出力 (DC1-5V リニア)
CHAMBER TEMPERATURE
(TYPE T)
MONITOR OUTPUT
(1-5V DC LINEAR)
記録計用出力
RECORDER OUTPUT